A dielectric resonator is a piece of dielectric (nonconductive but polarizable) material, usually ceramic, that is designed to function as a resonator for radio waves, generally in the microwave and millimeter wave bands. The microwaves are confined inside the resonator material by the abrupt change in permittivity at the surface, and bounce back and forth between the sides. At certain frequencies, the resonant frequencies, the microwaves form standing waves in the resonator, oscillating with large amplitudes. Dielectric resonators generally consist of a "puck" of ceramic that has a large dielectric constant and a low dissipation factor. The resonant frequency is determined by the overall physical dimensions of the resonator and the dielectric constant of the material.

Dielectric resonators function similarly to cavity resonators, hollow metal boxes that are also widely used as resonators at microwave frequencies, except that the radio waves are reflected by the large change in permittivity rather than by the conductivity of the metal. At millimeter wave frequencies, metal surfaces become lossy reflectors, so dielectric resonators are used at these frequencies. Dielectric resonators' main use is in millimeter-wave electronic oscillators (dielectric resonator oscillator, DRO) to control the frequency of the radio waves generated. They are also used as bandpass filters as well as antennas.

Historical overview

edit

In the late 19th century, Lord Rayleigh demonstrated that an infinitely long cylindrical rod made up of dielectric material could serve as a waveguide.[1] Additional theoretical [2] and experimental [3] work done in Germany in early 20th century, offered further insight into the behavior of electromagnetic waves in dielectric rod waveguides. Since a dielectric resonator can be thought of as a truncated dielectric rod waveguide, this research was essential for scientific understanding of electromagnetic phenomena in dielectric resonators. In 1939 Robert D. Richtmyer published a study [4] in which he showed that dielectric structures can act just as metallic cavity resonators. He appropriately named these structures dielectric resonators. Richtmyer also demonstrated that, if exposed to free space, dielectric resonators must radiate because of the boundary conditions at the dielectric-to-air interface. These results were later used in the development of DRA (Dielectric Resonator Antenna). Due to World War II, lack of advanced materials and adequate manufacturing techniques, dielectric resonators fell in relative obscurity for another two decades after Richtmyer's study was published. However, in the 1960s, as high-frequency electronics and modern communications industry started to take off, dielectric resonators gained in significance. They offered a size-reducing design alternative to bulky waveguide filters and lower-cost alternatives for electronic oscillator,[5] frequency selective limiter[6] and slow-wave [6] circuits. In addition to cost and size, other advantages that dielectric resonators have over conventional metal cavity resonators are lower weight, material availability, and ease of manufacturing. There is a vast availability of different dielectric resonators on the market today with unloaded Q factor on the order of 10000s.

Theory of operation

edit
 
Dielectric resonators can be mounted in waveguides to serve as microwave filters. This is a dielectric bandpass filter consisting of three dielectric resonators mounted in a transverse direction.

Although dielectric resonators display many similarities to resonant metal cavities, there is one important difference between the two: while the electric and magnetic fields are zero outside the walls of the metal cavity (i.e. open circuit boundary conditions are fully satisfied), these fields are not zero outside the dielectric walls of the resonator (i.e. open circuit boundary conditions are approximately satisfied). Even so, electric and magnetic fields decay from their maximum values considerably when they are away from the resonator walls. Most of the energy is stored in the resonator at a given resonant frequency for a sufficiently high dielectric constant  . Dielectric resonators can exhibit an extremely high Q factor that is comparable to a metal walled cavity.[7]

There are three types of resonant modes that can be excited in dielectric resonators: transverse electric (TE), transverse magnetic (TM) or hybrid electromagnetic (HEM) modes. Theoretically, there is an infinite number of modes in each of the three groups, and desired mode is usually selected based on the application requirements. Generally,   mode is used in most non-radiating applications, but other modes can have certain advantages for specific applications.[5]

Approximate resonant frequency of   mode for an isolated cylindrical dielectric resonator can be calculated as:[5]

 

Where   is the radius of the cylindrical resonator and what   is its length? Both   and   are in millimeters. Resonant frequency   is in gigahertz. This formula is accurate to about 2% in the range:

 

 

However, since a dielectric resonator is usually enclosed in a conducting cavity for most applications, the real resonant frequencies are different from the one calculated above. As conducting walls of the enclosing cavity approach the resonator, change in boundary conditions and field containment start to affect resonant frequencies. The size and type of the material encapsulating the cavity can drastically impact the performance of the resonant circuit. This phenomenon can be explained using cavity perturbation theory. If a resonator is enclosed in a metallic cavity, resonant frequencies change in following fashion:[5]

  • if the stored energy of the displaced field is mostly electric, its resonant frequency will decrease;
  • if the stored energy of the displaced field is mostly magnetic, its resonant frequency will increase. This happens to be the case for   mode.

The most common problem exhibited by dielectric resonator circuits is their sensitivity to temperature variation and mechanical vibrations.[8] Even though recent improvements in materials science and manufacturing mitigated some of these issues, compensating techniques still may be required to stabilize the circuit performance over temperature and frequency.

Common applications

edit

The most common applications,[5][9] of dielectric resonators are:

See also

edit

Notes

edit
  1. ^ Lord Rayleigh, “On the Passage of Waves Through Tubes, or the Vibration of Dielectric Cylinders”, Philosophical Magazine, Vol. 43, pp. 125–132, February 1897.
  2. ^ D. Hondros, “Ueber elektromagnetische Drahtwelle,” Annalen der Physik, Vol. 30, pp. 905–949, 1909.
  3. ^ H. Zahn, “Ueber den Nachweis elektromagnetischer Wellen an dielektrischen Draehten,”, Annalen der Physik, vol. 37, pp. 907–933, 1916.
  4. ^ R.D. Richtmyer, “Dielectric Resonators”, J.Appl. Phys., Vol. 10, pp. 391–398, June 1939.
  5. ^ a b c d e Darko Kajfez and Piere Guillon, Dielectric Resonators, Artech House, Dedham, MA, 1986.
  6. ^ a b Marian W. Pospieszalski, “Cylindrical Dielectric Resonators and Their Applications in TEM Line Microwave Circuits”, IEEE Trans. Microwave Theory Tech., Vol. MTT-27, pp. 233–238, March 1979.
  7. ^ A. Okaya and L.F. Barash, “The Dielectric Microwave Resonator”, Proc. IRE, Vol. 50, pp. 2081–2092, October 1962.
  8. ^ M.J. Loboda, T.E. Parker and G.K. Montress, "Temperature sensitivity of dielectric resonators and dielectric resonator oscillators," Proc. of the 42nd Annual Freq. Cont. Symp., pp. 263–271, Jun 1988.
  9. ^ J.K. Plourde and C. Ren, “Application of Dielectric Resonators in Microwave Components”, IEEE Trans. Microwave Theory Tech., Vol. MTT-29, pp. 754–769, August 1981.

References

edit
  • Lord Rayleigh, “On the Passage of Waves Through Tubes, or the Vibration of Dielectric Cylinders”, Philosophical Magazine, Vol. 43, pp. 125–132, February 1897.
  • D. Hondros, “Ueber elektromagnetische Drahtwelle,” Annalen der Physik, Vol. 30, pp. 905–949, 1909.
  • H. Zahn, “Ueber den Nachweis elektromagnetischer Wellen an dielektrischen Draehten,”, Annalen der Physik, vol. 37, pp. 907–933, 1916.
  • R.D. Richtmyer, “Dielectric Resonators”, J.Appl. Phys., Vol. 10, pp. 391–398, June 1939.
  • Darko Kajfez and Piere Guillon, Dielectric Resonators, Artech House, Dedham, MA, 1986.
  • Marian W. Pospieszalski, “Cylindrical Dielectric Resonators and Their Applications in TEM Line Microwave Circuits”, IEEE Trans. Microwave Theory Tech., Vol. MTT-27, pp. 233–238, March 1979.
  • A. Okaya and L.F. Barash, “The Dielectric Microwave Resonator”, Proc. IRE, Vol. 50, pp. 2081–2092, October 1962.
  • M.J. Loboda, T.E. Parker and G.K. Montress, "Temperature sensitivity of dielectric resonators and dielectric resonator oscillators," Proc. of the 42nd Annual Freq. Cont. Symp., pp. 263–271, Jun 1988.
  • J.K. Plourde and C. Ren, “Application of Dielectric Resonators in Microwave Components”, IEEE Trans. Microwave Theory Tech., Vol. MTT-29, pp. 754–769, August 1981.