A lenticular lens is an array of lenses, designed so that when viewed from slightly different angles, different parts of the image underneath are shown.[1][2][failed verification – see discussion] The most common example is the lenses used in lenticular printing, where the technology is used to give an illusion of depth, or to make images that appear to change or move as the image is viewed from different angles.
![](http://178.128.105.246/cars-http-upload.wikimedia.org/wikipedia/commons/thumb/f/ff/Sq3d-Feuille_lenticulaire.jpg/220px-Sq3d-Feuille_lenticulaire.jpg)
Applications
editLenticular printing
editLenticular printing is a multi-step process consisting of creating a lenticular image from at least two existing images, and combining it with a lenticular lens. This process can be used to create various frames of animation (for a motion effect), offsetting the various layers at different increments (for a 3D effect), or simply to show a set of alternate images which may appear to transform into each other.
Corrective lenses
editLenticular lenses are sometimes used as corrective lenses for improving vision. A bifocal lens could be considered a simple example.
Lenticular eyeglass lenses have been employed to correct extreme hyperopia (farsightedness), a condition often created by cataract surgery when lens implants are not possible. To limit the great thickness and weight that such high-power lenses would otherwise require, all the power of the lens is concentrated in a small area in the center. In appearance, such a lens is often described as resembling a fried egg: a hemisphere atop a flat surface. The flat surface or "carrier lens" has little or no power and is there merely to fill up the rest of the eyeglass frame and to hold or "carry" the lenticular portion of the lens. This portion is typically 40 mm (1.6 in) in diameter but may be smaller, as little as 20 mm (0.79 in), in sufficiently high powers. These lenses are generally used for plus (hyperopic) corrections at about 12 diopters or higher. A similar sort of eyeglass lens is the myodisc, sometimes termed a minus lenticular lens, used for very high negative (myopic) corrections. More aesthetic aspheric lens designs are sometimes fitted.[3] A film made of cylindrical lenses molded in a plastic substrate as shown in above picture, can be applied to the inside of standard glasses to correct for diplopia. The film is typically applied to the eye with the good muscle control of direction. Diplopia (also known as double vision) is typically caused by a sixth cranial nerve palsy that prevents full control of the muscles that control the direction the eye is pointed in. These films are defined in the number of degrees of correction that is needed where the higher the degree, the higher the directive correction that is needed.
Lenticular screens
editScreens with a molded lenticular surface are frequently used with projection television systems. In this case, the purpose of the lenses is to focus more of the light into a horizontal beam and allow less of the light to escape above and below the plane of the viewer. In this way, the apparent brightness of the image is increased.
Ordinary front-projection screens can also be described as lenticular. In this case, rather than transparent lenses, the shapes formed are tiny curved reflectors. Lenticular screens are most often used for ambient light rejecting projector screens for ultra-short throw projectors.[4] The lenticular structure of the surface reflects the light from the projector to the viewer without reflecting the light from sources above the screen.
3D television
editAs of 2010[update], a number of manufacturers were developing auto-stereoscopic high definition 3D televisions, using lenticular lens systems to avoid the need for special spectacles. One of these, Chinese manufacturer TCL, was selling a 42-inch (110 cm) LCD model—the TD-42F—in China for around US$20,000.[5]
In 2021 only specialist manufacturers are making these kinds of display.[6]
Lenticular color motion picture processes
editLenticular lenses were used in early color motion picture processes of the 1920s such as the Keller-Dorian system and Kodacolor. This enabled color pictures with the use of merely monochrome film stock.[7]
Angle of view of a lenticular print
editThe angle of view of a lenticular print is the range of angles within which the observer can see the entire image. This is determined by the maximum angle at which a ray can leave the image through the correct lenticule.
Angle within the lens
editThe diagram at right shows in green the most extreme ray within the lenticular lens that will be refracted correctly by the lens. This ray leaves one edge of an image strip (at the lower right) and exits through the opposite edge of the corresponding lenticule.
Definitions
edit- is the angle between the extreme ray and the normal at the point where it exits the lens,
- is the pitch, or width of each lenticular cell,
- is the radius of curvature of the lenticule,
- is the thickness of the lenticular lens
- is the thickness of the substrate below the curved surface of the lens, and
- is the lens's index of refraction.
Calculation
edit- ,
where
- ,
- is the distance from the back of the grating to the edge of the lenticule, and
- .
Angle outside the lens
editThe angle outside the lens is given by refraction of the ray determined above. The full angle of observation is given by
- ,
where is the angle between the extreme ray and the normal outside the lens. From Snell's Law,
- ,
where is the index of refraction of air.
Example
editConsider a lenticular print that has lenses with 336.65 μm pitch, 190.5 μm radius of curvature, 457 μm thickness, and an index of refraction of 1.557. The full angle of observation would be 64.6°.
Rear focal plane of a lenticular network
editThe focal length of the lens is calculated from the lensmaker's equation, which in this case simplifies to:
- ,
where is the focal length of the lens.
The back focal plane is located at a distance from the back of the lens:
A negative BFD indicates that the focal plane lies inside the lens.
In most cases, lenticular lenses are designed to have the rear focal plane coincide with the back plane of the lens. The condition for this coincidence is , or
This equation imposes a relation between the lens thickness and its radius of curvature .
Example
editThe lenticular lens in the example above has focal length 342 μm and back focal distance 48 μm, indicating that the focal plane of the lens falls 48 micrometers behind the image printed on the back of the lens.
See also
edit- Fresnel lens, a different 'flat' lens technology
- Integral imaging
- Microlens
References
edit- ^ "Lenticular, how it works". Lenstar.org. Archived from the original on 3 May 2016. Retrieved 25 May 2017.
- ^ DIY Printed Holographic Display (Lenticular Optics Explained), archived from the original on 21 December 2021, retrieved 8 May 2021
- ^ Jalie, Mo (2003). Ophthalmic Lenses and Dispensing. Elsevier Health Sciences. p. 178. ISBN 0-7506-5526-7.
- ^ "Lenticular projector screen vs. Fresnel projector screen for ultra short throws". ProjectorScreen.com. Retrieved 15 June 2022.
- ^ "Give Me 3D TV, Without The Glasses". Archived from the original on 13 February 2010. Retrieved 6 May 2010.
- ^ Factory, Looking Glass. "Looking Glass Factory · The World's Leading Holographic Display". Looking Glass Factory · The World's Leading Holographic Display. Retrieved 8 May 2021.
- ^ "Lenticular films on Timeline of Historical Film Colors". Archived from the original on 9 July 2014. Retrieved 29 June 2014.
- Bartholdi, Paul (1997). "Quelques notions d'optique" (in French). Observatoire de Genève. Retrieved 19 December 2007.
- Soulier, Bernard (2002). "Principe de fonctionnement de l'optique lenticulaire" (in French). Séquence 3d. Retrieved 22 December 2007.
- Okoshi, Takanori Three-Dimensional Imaging Techniques Atara Press (2011), ISBN 978-0-9822251-4-1.