the crank, and hence to find the displacement of the valve at any
position of the crank we have only to draw CQ in fig. 26 parallel
to the crank, when CQ represents the
Fig. 27.
displacement of the valve to the scale
on which the diameter of each valve
circle represents the half-travel of the
valve. CQ0 is the valve displacement
at the beginning of the stroke shown
by the arrow. Draw circular arcs ๐๐
and ๐๐ with C as centre and with radii
equal to the outside lap and the
inside lap ๐ respectively. C๐ is the
position of the crank at which preadmission
occurs. The lead is ๐0Q0.
The greatest steam opening is ๐1B.
The cut-off occurs when the crank has
the direction C๐. C๐ is the position
of the crank at release, and C๐ marks the end of the exhaust.
63. In this diagram radii drawn from C mark the angular positions of the crank and their intercepts by the valve circles determine the corresponding displacement of the valve. It remains to find the corresponding displacement of the piston. For this Zeuner employs a supplementary graphic construction, shown in fig. 27. Here ๐๐ or ๐โฒ๐โฒ represents the connecting rod, and ๐๐ or ๐โฒ๐ the crank. With centre ๐ and radius ๐๐ a circle ๐๐ is drawn, and with centre ๐ and radius ๐๐ another circle ๐๐. Then for any position of the crank, as ๐๐โฒ, the intercept ๐๐ between the circles is easily seen to be equal to ๐๐โฒ, and is therefore the distance by which the piston has moved from its extreme position at the beginning of the stroke. In practice this diagram is combined with that of fig. 26, by drawing both about the same centre and using different scales for valve and piston travel A radius vector drawn from the centre parallel to the crank in any position then shows the valveโs displacement from the valveโs middle position by the intercept CQ of fig. 26, and the pistonโs displacement from the beginning of the pistonโs motion by the intercept ๐๐ of fig. 27.
64. In the figures which have been sketched the events refer to the front end of the cylinder, that is, the end nearest to the crank (see fig. 23). To determine the events of steam distribution at the back end, the lap circles shown by dotted lines in fig. 26 must also be drawn, C๐โฒ being the outside lap for the back end, and C๐โฒ the inside lap. These laps are not necessarily equal to those at the other end of the valve. From the diagrams it will be seen that, especially with a short connecting-rod, the cut-off and release occur earlier and the compression later at the front than at the back end if the laps are equal, and a more symmetrical steam distribution can be produced by making the inside lap greater and the outside lap less on the side which leads to the front end of the cylinder On the other hand, an unsymmetrical distribution may be desirable as in a vertical engine, where the weight of the piston assists the steam during the down-stroke and resists it during the up-stroke and this may be secured by a suitable inequality in the laps
65. By varying the ratio of the laps ๐ and ๐ to the travel of the valve, we produce effects on the steam distribution which are readily traced by means of the diagram. Reduction of travel (which is equivalent to increase of both ๐ and ๐) gives later preadmission, earlier cut-off, later release and earlier compression; the ratios of expansion and of compression are both increased. Increase of angular advance accelerates all the events and causes a slight increase in the ratio of expansion.
66. In designing a slide-valve the breadth of the steam ports in the direction of the valveโs motion is determined with reference to the volume of the exhaust steam to be discharged in a given time the area of the ports being generally such that the mean velocity of the steam during discharge is less than 100 ft. per second The travel is made great enough to keep the cylinder port fully open during the greater part of the exhaust; for this purpose it is 212 or 3 times the breadth of the steam port. To facilitate the exit of steam the inside lap is always small, and is often wanting or even negative. During admission the steam port is rarely quite uncovered, especially if the outside lap is large and the travel moderate. Large travel has the advantage of giving freer ingress and egress of steam, with more sharply-defined cut-off, compression and release but this advantage is secured at the cost of more work spent in moving the valve and more wear of the faces. To lessen the necessary travel without reducing the area of steam ports, double-ported valves are often used. An example is shown below in fig. 39.
67. Reversal of Motion with Slide-Valve.โThe eccentric must
stand in advance of the crank by the angle 90ยฐ + ฮธ, as in fig. 28, where CK is the crank, and CE the corresponding
position of the eccentric when the engine is running
in the direction of the arrow ๐. To set the engine
Fig. 28.
in gear to run in the opposite direction (๐) it is
only necessary to shift the eccentric into the position
CEโฒ when it will still be 90ยฐ + ฮธ in advance of the
crank. In the older engines this reversal was effected
by temporarily disengaging the eccentric-rod from the valve-rod,
working the valve by hand until the crank turned back through
an angle equal to ECEโฒ, the eccentric meanwhile remaining
at rest, and then re-engaging the gear.
instead of being keyed to the shaft,
fixed to the shaft, which abutted on
shoulders projecting from the sheave.
reversing gear means are provided for turning the eccentric round
on the shaft, but the arrangement known as the link-motion is now
the most usual gear in locomotive, marine, winding and other
engines which require to be often and easily reversed.
68. Link-Motion.โIn the link-motion two eccentrics are used, and the ends of their rods are connected by a link. In Stephensonโs link-motionโthe earliest and still the most usual formโthe link is a slotted bar or pair of bars curved to the same radius as the eccentric rods (fig. 29), and capable of being shifted up or down by a suspension rod. The valve-rod ends in a block which slides within the link, and when the link is placed so that this block is nearly in line with the forward eccentric rod (R. fig. 29) the valve moves in nearly the same way as if it were driven directly by a single eccentric.
This is the position of โfull forward gear.โ In โfull backward gear,โ on the other hand, the link is pulled up until the block is in nearly a line with the backward eccentric rod Rโฒ. The link-motion thus gives a ready means of reversing the engineโbut it does more than this. By setting the link in an intermediate position the valve receives a motion nearly the same as that which would be given by an eccentric of shorter radius and of greater angular advance, and the effect is to give a distribution of steam in which the cut-off is earlier than in full gear, and the expansion and compression are greater. In mid gear the steam distribution is such that scarcely any work is done in the cylinder. The movement of the link, is effected by a hand-lever, or by a screw, or (in large engines) by an auxiliary steam engine. A usual arrangement of hand-lever, sketched in fig. 29, has given rise to the phrase โnotching up,โ to describe the setting of the link to give a greater degree of expansion.
In Goochโs link-motion (fig. 30) the link is not moved up in shifting from forward to backward gear, but a radius rod between the valve-rod and the link (which is curved to suit this radius rod) is raised or loweredโa plan which has the advantage that the lead is the same in all gears. In Allanโs motion (fig. 31) the change of gear is effected partly by shifting the link and partly by shifting a radius rod, and the link is straight.
69. Graphic Solution of Link-Motion.โThe movement of a valve driven by a link-motion may be very fully and exactly analysed by drawing with the aid of a template the positions of the centre line of the link corresponding to a number of successive positions of the crank. Thus, in fig. 32, two circular arcs passing through ๐ and ๐โฒ are drawn with E and Eโฒ as centres and the eccentric rods are radii. These are loci of two known points of the link, and a third locus is the circle ๐ in which the point of suspension must lie. By placing on the paper a template of the link, with these three points marked