An azeotrope (/əˈziːəˌtroʊp/)[1] or a constant heating point mixture is a mixture of two or more components in fluidic states whose proportions cannot be altered or changed by simple distillation.[2] This happens because when an azeotrope is boiled, the vapour has the same proportions of constituents as the unboiled mixture. Azeotropic mixture behavior is important for fluid separation processes.
![](http://178.128.105.246/content-http-upload.wikimedia.org/wikipedia/commons/thumb/f/fa/VLEIsoropanolWaterAzeotrope.png/330px-VLEIsoropanolWaterAzeotrope.png)
Each azeotrope has a characteristic boiling point. The boiling point of an azeotrope is either less than the boiling point temperatures of any of its constituents (a positive azeotrope), or greater than the boiling point of any of its constituents (a negative azeotrope). For both positive and negative azeotropes, it is not possible to separate the components by fractional distillation and azeotropic distillation is usually used instead.
For technical applications, the pressure-temperature-composition behavior of a mixture is the most important, but other important thermophysical properties are also strongly influenced by azeotropy, including the surface tension[3][4][5] and transport properties.[6][7]
Some azeotropic mixtures of pairs of compounds are known,[8] and many azeotropes of three or more compounds are also known.[9]
Etymology
editThe term azeotrope is derived from the Greek words ζέειν (boil) and τρόπος (turning) with the prefix α- (no) to give the overall meaning, "no change on boiling". The term was coined in 1911 by English chemist John Wade[10] and Richard William Merriman.[11] Because their composition is unchanged by distillation, azeotropes are also called (especially in older texts) constant boiling point mixtures.
Types
editPositive azeotropes
editA solution that shows greater positive deviation from Raoult's law forms a minimum boiling azeotrope at a specific composition. In general, a positive azeotrope boils at a lower temperature than any other ratio of its constituents. Positive azeotropes are also called minimum boiling mixtures or pressure maximum azeotropes. A well-known example of a positive azeotrope is an ethanol–water mixture (obtained by fermentation of sugars) consisting of 95.63% ethanol and 4.37% water (by mass), which boils at 78.2 °C.[12] Ethanol boils at 78.4 °C, water boils at 100 °C, but the azeotrope boils at 78.2 °C, which is lower than either of its constituents.[13] Indeed, 78.2 °C is the minimum temperature at which any ethanol/water solution can boil at atmospheric pressure. Once this composition has been achieved, the liquid and vapour have the same composition, and no further separation occurs.
The boiling and recondensation of a mixture of two solvents are changes of chemical state; as such, they are best illustrated with a phase diagram. If the pressure is held constant, the two variable parameters are the temperature and the composition.
The adjacent diagram shows a positive azeotrope of hypothetical constituents, X and Y. The bottom trace illustrates the boiling temperature of various compositions. Below the bottom trace, only the liquid phase is in equilibrium. The top trace illustrates the vapor composition above the liquid at a given temperature. Above the top trace, only the vapor is in equilibrium. Between the two traces, liquid and vapor phases exist simultaneously in equilibrium: for example, heating a 25% X : 75% Y mixture to temperature AB would generate vapor of composition B over liquid of composition A. The azeotrope is the point on the diagram where the two curves touch. The horizontal and vertical steps show the path of repeated distillations. Point A is the boiling point of a nonazeotropic mixture. The vapor that separates at that temperature has composition B. The shape of the curves requires that the vapor at B be richer in constituent X than the liquid at point A.[2] The vapor is physically separated from the VLE (vapor-liquid equilibrium) system and is cooled to point C, where it condenses. The resulting liquid (point C) is now richer in X than it was at point A. If the collected liquid is boiled again, it progresses to point D, and so on. The stepwise progression shows how repeated distillation can never produce a distillate that is richer in constituent X than the azeotrope. Note that starting to the right of the azeotrope point results in the same stepwise process closing in on the azeotrope point from the other direction.
Negative azeotropes
editA solution that shows large negative deviation from Raoult's law forms a maximum boiling azeotrope at a specific composition. Nitric acid and water is an example of this class of azeotrope. This azeotrope has an approximate composition of 68% nitric acid and 32% water by mass, with a boiling point of 393.5 K (120.4 °C). In general, a negative azeotrope boils at a higher temperature than any other ratio of its constituents. Negative azeotropes are also called maximum boiling mixtures or pressure minimum azeotropes. An example of a negative azeotrope is hydrochloric acid at a concentration of 20.2% and 79.8% water (by mass). Hydrogen chloride boils at -85 °C and water at 100 °C, but the azeotrope boils at 110 °C, which is higher than either of its constituents. The maximum boiling point of any hydrochloric acid solution is 110 °C. Other examples:
- hydrofluoric acid (35.6%) / water, boils at 111.35 °C
- nitric acid (68%) / water, boils at 120.2 °C at 1 atm
- perchloric acid (71.6%) / water, boils at 203 °C
- sulfuric acid (98.3%) / water, boils at 338 °C
The adjacent diagram shows a negative azeotrope of ideal constituents, X and Y. Again the bottom trace illustrates the boiling temperature at various compositions, and again, below the bottom trace the mixture must be entirely liquid phase. The top trace again illustrates the condensation temperature of various compositions, and again, above the top trace the mixture must be entirely vapor phase. The point, A, shown here is a boiling point with a composition chosen very near to the azeotrope. The vapor is collected at the same temperature at point B. That vapor is cooled, condensed, and collected at point C. Because this example is a negative azeotrope rather than a positive one, the distillate is farther from the azeotrope than the original liquid mixture at point A was. So the distillate is poorer in constituent X and richer in constituent Y than the original mixture. Because this process has removed a greater fraction of Y from the liquid than it had originally, the residue must be poorer in Y and richer in X after distillation than before.
If the point, A had been chosen to the right of the azeotrope rather than to the left, the distillate at point C would be farther to the right than A, which is to say that the distillate would be richer in X and poorer in Y than the original mixture. So in this case too, the distillate moves away from the azeotrope and the residue moves toward it. This is characteristic of negative azeotropes. No amount of distillation, however, can make either the distillate or the residue arrive on the opposite side of the azeotrope from the original mixture. This is characteristic of all azeotropes.
Double azeotropes
editAlso more complex azeotropes exist, which comprise both a minimum-boiling and a maximum-boiling point. Such a system is called a double azeotrope, and will have two azeotropic compositions and boiling points. An example is water and N-methylethylenediamine[14] as well as benzene and hexafluorobenzene.
Complex systems
editSome azeotropes fit into neither the positive nor negative categories. The best known of these is the ternary azeotrope formed by 30% acetone, 47% chloroform, and 23% methanol, which boils at 57.5 °C. Each pair of these constituents forms a binary azeotrope, but chloroform/methanol and acetone/methanol both form positive azeotropes while chloroform/acetone forms a negative azeotrope. The resulting ternary azeotrope is neither positive nor negative. Its boiling point falls between the boiling points of acetone and chloroform, so it is neither a maximum nor a minimum boiling point. This type of system is called a saddle azeotrope.[8] Only systems of three or more constituents can form saddle azeotropes.
Miscibility and zeotropy
editIf the constituents of a mixture are completely miscible in all proportions with each other, the type of azeotrope is called a homogeneous azeotrope. Homogeneous azeotropes can be of the low-boiling or high-boiling azeotropic type. For example, any amount of ethanol can be mixed with any amount of water to form a homogeneous solution.
If the components of a mixture are not completely miscible, an azeotrope can be found inside the miscibility gap. This type of azeotrope is called a heterogeneous azeotrope or heteroazeotrope. A heteroazeotropic distillation will have two liquid phases. Heterogeneous azeotropes are only known in combination with temperature-minimum azeotropic behavior. For example, if equal volumes of chloroform (water solubility 0.8 g/100 ml at 20 °C) and water are shaken together and then left to stand, the liquid will separate into two layers. Analysis of the layers shows that the top layer is mostly water with a small amount of chloroform dissolved in it, and the bottom layer is mostly chloroform with a small amount of water dissolved in it. If the two layers are heated together, the system of layers will boil at 53.3 °C, which is lower than either the boiling point of chloroform (61.2 °C) or the boiling point of water (100 °C). The vapor will consist of 97.0% chloroform and 3.0% water regardless of how much of each liquid layer is present provided both layers are indeed present. If the vapor is re-condensed, the layers will reform in the condensate, and will do so in a fixed ratio, which in this case is 4.4% of the volume in the top layer and 95.6% in the bottom layer.[15]
Combinations of solvents that do not form an azeotrope when mixed in any proportion are said to be zeotropic. Azeotropes are useful in separating zeotropic mixtures. An example is zeotropic acetic acid and water. It is very difficult to separate out pure acetic acid (boiling point: 118.1 °C): progressive distillations produce drier solutions, but each further distillation becomes less effective at removing the remaining water. Distilling the solution to dry acetic acid is therefore economically impractical. But ethyl acetate forms an azeotrope with water that boils at 70.4 °C. By adding ethyl acetate as an entrainer, it is possible to distill away the azeotrope and leave nearly pure acetic acid as the residue.
Number of constituents
editAzeotropes consisting of two constituents are called binary azeotropes such as diethyl ether (33%) / halothane (66%) a mixture once commonly used in anesthesia. Azeotropes consisting of three constituents are called ternary azeotropes, e.g. acetone / methanol / chloroform. Azeotropes of more than three constituents are also known.
Condition of existence
editThe condition relates activity coefficients in liquid phase to total pressure and the vapour pressures of pure components.
Azeotropes can form only when a mixture deviates from Raoult's law, the equality of compositions in liquid phase and vapor phases, in vapour-liquid equilibrium and Dalton's law the equality of pressures for total pressure being equal to the sum of the partial pressures in real mixtures.
In other words: Raoult's law predicts the vapor pressures of ideal mixtures as a function of composition ratio. More simply: per Raoult's law molecules of the constituents stick to each other to the same degree as they do to themselves. For example, if the constituents are X and Y, then X sticks to Y with roughly equal energy as X does with X and Y does with Y. A positive deviation from Raoult's law results when the constituents have a disaffinity for each other – that is X sticks to X and Y to Y better than X sticks to Y. Because this results in the mixture having less total affinity of the molecules than the pure constituents, they more readily escape from the stuck-together phase, which is to say the liquid phase, and into the vapor phase. When X sticks to Y more aggressively than X does to X and Y does to Y, the result is a negative deviation from Raoult's law. In this case because the molecules in the mixture are sticking together more than in the pure constituents, they are more reluctant to escape the stuck-together liquid phase.[2]
When the deviation is great enough to cause a maximum or minimum in the vapor pressure versus composition function, it is a mathematical consequence that at that point, the vapor will have the same composition as the liquid, resulting in an azeotrope.
The adjacent diagram illustrates total vapor pressure of three hypothetical mixtures of constituents, X, and Y. The temperature throughout the plot is assumed to be constant. The center trace is a straight line, which is what Raoult's law predicts for an ideal mixture. In general solely mixtures of chemically similar solvents, such as n-hexane with n-heptane, form nearly ideal mixtures that come close to obeying Raoult's law. The top trace illustrates a nonideal mixture that has a positive deviation from Raoult's law, where the total combined vapor pressure of constituents, X and Y, is greater than what is predicted by Raoult's law. The top trace deviates sufficiently that there is a point on the curve where its tangent is horizontal. Whenever a mixture has a positive deviation and has a point at which the tangent is horizontal, the composition at that point is a positive azeotrope.[17] At that point the total vapor pressure is at a maximum. Likewise the bottom trace illustrates a nonideal mixture that has a negative deviation from Raoult's law, and at the composition where tangent to the trace is horizontal there is a negative azeotrope. This is also the point where total vapor pressure is minimum.[17]
Separation
editIf the two solvents can form a negative azeotrope, then distillation of any mixture of those constituents will result in the residue being closer to the composition at the azeotrope than the original mixture. For example, if a hydrochloric acid solution contains less than 20.2% hydrogen chloride, boiling the mixture will leave behind a solution that is richer in hydrogen chloride than the original. If the solution initially contains more than 20.2% hydrogen chloride, then boiling will leave behind a solution that is poorer in hydrogen chloride than the original. Boiling of any hydrochloric acid solution long enough will cause the solution left behind to approach the azeotropic ratio.[18] On the other hand, if two solvents can form a positive azeotrope, then distillation of any mixture of those constituents will result in the residue away from the composition at the azeotrope than the original mixture. For example, if a 50/50 mixture of ethanol and water is distilled once, the distillate will be 80% ethanol and 20% water, which is closer to the azeotropic mixture than the original, which means the solution left behind will be poorer in ethanol.[19] Distilling the 80/20% mixture produces a distillate that is 87% ethanol and 13% water. Further repeated distillations will produce mixtures that are progressively closer to the azeotropic ratio of 95.5/4.5%. No numbers of distillations will ever result in a distillate that exceeds the azeotropic ratio. Likewise, when distilling a mixture of ethanol and water that is richer in ethanol than the azeotrope, the distillate (contrary to intuition) will be poorer in ethanol than the original but still richer than the azeotrope.[20]
Distillation is one of the primary tools that chemists and chemical engineers use to separate mixtures into their constituents. Because distillation cannot separate the constituents of an azeotrope, the separation of azeotropic mixtures (also called azeotrope breaking) is a topic of considerable interest.[8] Indeed, this difficulty led some early investigators to believe that azeotropes were actually compounds of their constituents.[2] But there are two reasons for believing that this is not the case. One is that the molar ratio of the constituents of an azeotrope is not generally the ratio of small integers. For example, the azeotrope formed by water and acetonitrile contains 2.253 moles (or 9/4 with a relative error of just 2%) of acetonitrile for each mole of water.[21] A more compelling reason for believing that azeotropes are not compounds is, as discussed in the last section, that the composition of an azeotrope can be affected by pressure. Contrast that with a true compound, carbon dioxide for example, which is two moles of oxygen for each mole of carbon no matter what pressure the gas is observed at. That azeotropic composition can be affected by pressure suggests a means by which such a mixture can be separated.
Pressure swing distillation
editA hypothetical azeotrope of constituents X and Y is shown in the adjacent diagram. Two sets of curves on a phase diagram one at an arbitrarily chosen low pressure and another at an arbitrarily chosen, but higher, pressure. The composition of the azeotrope is substantially different between the high- and low-pressure plots: higher in X for the high-pressure system. The goal is to separate X in as high a concentration as possible starting from point A. At the low pressure, it is possible by progressive distillation to reach a distillate at the point, B, which is on the same side of the azeotrope as A. Successive distillation steps near the azeotropic composition exhibit very little difference in boiling temperature. If this distillate is now exposed to the high pressure, it boils at point C. From C, by progressive distillation it is possible to reach a distillate at the point D, which is on the same side of the high-pressure azeotrope as C. If that distillate is then exposed again to the low pressure, it boils at point E, which is on the opposite side of the low-pressure azeotrope to A. So, by means of the pressure swing, it is possible to cross over the low-pressure azeotrope.
When the solution is boiled at point E, the distillate is poorer in X than the residue at point E. This means that the residue is richer in X than the distillate at point E. Indeed, progressive distillation can produce a residue as rich in X as is required.
In summary:
- Low-pressure rectification (A to B)
- High-pressure rectification (C to D)
- Low-pressure stripping (E to target purity)
- Rectification: the distillate, or "tops", is retained and exhibits an increasingly lower boiling point.
- Stripping: the residue, or "bottoms", is retained and exhibits an increasingly higher boiling point.
A mixture of 5% water with 95% tetrahydrofuran is an example of an azeotrope that can be economically separated using a pressure swing: a swing in this case between 1 atm and 8 atm. By contrast the composition of the water to ethanol azeotrope discussed earlier is not affected enough by pressure to be easily separated using pressure swings[8] and instead, an entrainer may be added that either modifies the azeotropic composition and exhibits immiscibility with one of the components, or extractive distillation may be used.[22]
Azeotropic distillation
editOther methods of separation involve introducing an additional agent, called an entrainer, that will affect the volatility of one of the azeotrope constituents more than another. When an entrainer is added to a binary azeotrope to form a ternary azeotrope, and the resulting mixture distilled, the method is called azeotropic distillation. The best known example is adding benzene or cyclohexane to the water/ethanol azeotrope. With cyclohexane as the entrainer, the ternary azeotrope is 7% water, 17% ethanol, and 76% cyclohexane, and boils at 62.1 °C.[23] Just enough cyclohexane is added to the water/ethanol azeotrope to engage all of the water into the ternary azeotrope. When the mixture is then boiled, the azeotrope vaporizes leaving a residue composed almost entirely of the excess ethanol.[8]
Chemical action separation
editAnother type of entrainer is one that has a strong chemical affinity for one of the constituents. Using again the example of the water/ethanol azeotrope, the liquid can be shaken with calcium oxide, which reacts strongly with water to form the nonvolatile compound, calcium hydroxide. Nearly all of the calcium hydroxide can be separated by filtration and the filtrate redistilled to obtain 100% pure ethanol. A more extreme example is the azeotrope of 1.2% water with 98.8% diethyl ether. Ether holds the last bit of water so tenaciously that only a very powerful desiccant such as sodium metal added to the liquid phase can result in completely dry ether.[24] Anhydrous calcium chloride is used as a desiccant for drying a wide variety of solvents since it is inexpensive and does not react with most nonaqueous solvents. Chloroform is an example of a solvent that can be effectively dried using calcium chloride.[24]
Distillation using a dissolved salt
editWhen a salt is dissolved in a solvent, it always has the effect of raising the boiling point of that solvent – that is it decreases the volatility of the solvent. When the salt is readily soluble in one constituent of a mixture but not in another, the volatility of the constituent in which it is soluble is decreased and the other constituent is unaffected. In this way, for example, it is possible to break the water/ethanol azeotrope by dissolving potassium acetate in it and distilling the result.[8]
Extractive distillation
editExtractive distillation is similar to azeotropic distillation, except in this case the entrainer is less volatile than any of the azeotrope's constituents. For example, the azeotrope of 20% acetone with 80% chloroform can be broken by adding water and distilling the result. The water forms a separate layer in which the acetone preferentially dissolves. The result is that the distillate is richer in chloroform than the original azeotrope.[8]
Pervaporation and other membrane methods
editThe pervaporation method uses a membrane that is more permeable to the one constituent than to another to separate the constituents of an azeotrope as it passes from liquid to vapor phase. The membrane is rigged to lie between the liquid and vapor phases. Another membrane method is vapor permeation, where the constituents pass through the membrane entirely in the vapor phase. In all membrane methods, the membrane separates the fluid passing through it into a permeate (that which passes through) and a retentate (that which is left behind). When the membrane is chosen so that is it more permeable to one constituent than another, then the permeate will be richer in that first constituent than the retentate.[8]
See also
editReferences
edit- ^ "Azeotrope definition and meaning - Collins English Dictionary". www.collinsdictionary.com.
- ^ a b c d e Moore, Walter J. Physical Chemistry, 3rd e Prentice-Hall 1962, pp. 140–142
- ^ Staubach, Jens; Stephan, Simon (28 September 2022). "Interfacial properties of binary azeotropic mixtures of simple fluids: Molecular dynamics simulation and density gradient theory". The Journal of Chemical Physics. 157 (12): 124702. doi:10.1063/5.0100728. ISSN 0021-9606.
- ^ McLure, I. A.; Edmonds, B.; Lal, M. (1973). "Extremes in Surface Tension of Fluorocarbon + Hydrocarbon Mixtures". Nature Physical Science. 241 (107): 71–71. doi:10.1038/physci241071a0. ISSN 0300-8746.
- ^ Schäfer, Elisabeth; Sadowski, Gabriele; Enders, Sabine (January 2014). "Interfacial tension of binary mixtures exhibiting azeotropic behavior: Measurement and modeling with PCP-SAFT combined with Density Gradient Theory". Fluid Phase Equilibria. 362: 151–162. doi:10.1016/j.fluid.2013.09.042. ISSN 0378-3812.
- ^ "95/05209 Transport properties of ternary near-azeotropic mixtures". Fuel and Energy Abstracts. 36 (5): 365. September 2009. doi:10.1016/0140-6701(95)96948-c. ISSN 0140-6701. Retrieved 24 March 2007.
- ^ Fertig, David; Hasse, Hans; Stephan, Simon (December 2002). "Transport properties of binary Lennard-Jones mixtures: Insights from entropy scaling and conformal solution theory". Journal of Molecular Liquids. 367: 120401. doi:10.1016/j.molliq.2022.120401. ISSN 0167-7322.
- ^ a b c d e f g h i Hilmen, Eva-Katrine (November 2000). "Separation of Azeotropic Mixtures: Tools for Analysis and Studies on Batch Distillation Operation" (PDF). Norwegian University of Science and Technology, Dept. of Chemical Engineering. Archived from the original (PDF) on 15 June 2007. Retrieved 24 March 2007.
- ^ Department of Chemical Engineering University of Alicante. "Numerical Determination of Distillation Boundaries for Multicomponent Homogeneous and Heterogeneous Azeotropic Systems" (PDF). Archived from the original (PDF) on 1 October 2011.
- ^ F. Gowland Hopkins (1913) "Obituary Notices: John Wade," Journal of the Chemical Society Transactions, 103 : 767-774.
- ^ Wade, John; Merriman, Richard William (1911). "Influence of water on the boiling point of ethyl alcohol at pressures above and below the atmospheric pressure". Journal of the Chemical Society, Transactions. 99: 997–1011. doi:10.1039/CT9119900997. From p. 1004: " … it is proposed, in order to avoid the cumbrous periphrase "mixtures having a minimum (or maximum) boiling point," to designate them as azeotropic mixtures (α, privative; ζέω, to boil)."
- ^ National Institute of Standards and Technology. "Standard Reference Material 1828: Ethanol-Water Solutions" (PDF). Archived from the original (PDF) on 8 June 2011.
- ^ Rousseau, Ronald W.; James R. Fair (1987). Handbook of separation process technology. Wiley-IEEE. pp. 261–262. ISBN 978-0-471-89558-9.
- ^ Olson, John D. "Thermodynamics of Hydrogen Bonding Mixtures 4" (PDF). Archived from the original (PDF) on 16 September 2008. Retrieved 27 January 2008.
- ^ CRC Handbook of Chemistry and Physics, 44th ed., p. 2156.
- ^ David, C. W., https://opencommons.uconn.edu/chem_educ/107
- ^ a b Jim Clark. "Nonideal Mixtures of Liquids". Chemguide.co.uk. Archived from the original on 20 February 2008. Retrieved 5 March 2008.
- ^ Merck Index of Chemicals and Drugs, 9th ed., monograph 4667
- ^ Clark, Jim (February 2014). "Non-Ideal Mixtures of Liquids". chemguide.co.uk.
- ^ Morrison, Robert Thornton; Boyd, Robert Neilson, Organic Chemistry, 2nd ed., Allyn and Bacon, 1972, p. 508
- ^ Ponton, Jack (September 2001). "Azeotrope Databank". The Edinburgh Collection of Open Software for Simulation and Education, University of Edinburgh. Archived from the original (Queriable database) on 24 April 2007. Retrieved 14 April 2007.
- ^ Perry's Chemical Engineer's Handbook, 7th Ed. 1997
- ^ CRC Handbook of Chemistry and Physics, 44th ed., p. 2181
- ^ a b Cohen, Julius B. Practical Organic Chemistry MacMillan 1930
External links
edit- "Publications about the separation of the azeotropes". BUTE Department of Process Engineering, Hungary. Retrieved 9 April 2007.
- "What is an Azeotrope?". B/R Corporation. Archived from the original on 24 April 2007. Retrieved 24 March 2007.
- Azeotrope defined with a limerick.
- Busato, Dr. G.A.; Bashein, Professor G. (2004). "The halothane/ether azeotrope – A reconsideration". Update in Anaesthesia. 18. Archived from the original (PDF) on 2 February 2016. Retrieved 26 September 2014.
- Ponton, Jack (September 2001). "Azeotrope Databank". The Edinburgh Collection of Open Software for Simulation and Education, University of Edinburgh. Archived from the original (Queriable database) on 24 April 2007. Retrieved 9 April 2007.
- Prediction of azeotropic behaviour by the inversion of functions from the plane to the plane
- Azeotropes on YouTube